H Frame Hydraulic Press

Product Details:

Frame Contraction: Frame fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable of generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.

Product Details:

Frame Contraction: Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron/steel fabricated and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.183

Product Details:

Frame Contraction: Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron/steel fabricated and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.

Product Details:

Frame Contraction: Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

 Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron/steel fabricated and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.

Product Details:

H Frame Type Hydraulic Press for many different applications; our hydraulic press designs can be broken down into basic categories to include: two post presses, four post Presses, C-frame presses, vertical presses and horizontal hydraulic presses.

The most common press design is the four post hydraulic press. This design is the most versatile as a result of having no size limits, and can be adapted to nearly any process. The four post press design can be configured in a vertical or horizontal position as the process and space available dictate. Precise control Technologies ensures that the four post presses are precise and efficient. Operator access is allowed from all four sides of the hydraulic press so it is very well suited for many different applications.

The C-frame press derives its name from the shape of the frame. The primary advantages to the C-frame design are an open work area and increased accessibility. The C-frame press features become even more advantageous when multiple presses are used for progressive operations with automated material handling moving parts from press to press. The C-Frame hydraulic presses, however, are generally limited in maximum tonnage due to the design.

The two post hydraulic press is basically a hybrid of the previous two designs. It has good accessibility of the work are for the operator and maintenance personnel while generally allowing for higher tonnage ratings than the C-frame press.

Advanced Machine Design Company utilizes over 26 years of engineering knowledge and experience to design and manufacture heavy duty state of the art hydraulic presses. Our presses are available in standard designs or can be customized to individual specifications. Advanced Machine Design Company Hydraulic Presses can be supplied with entry and exit automated material handling with the value added of purchasing an entire turnkey system from one vendor.

Standard Press Features:

• PLC Control with digital operator interface
• Meets or exceeds OSHA regulations for safety
• Heavy duty industrial design with 4 to 1 safety factor
• Guarding to individual specifications with E-Stop circuits
• Minimal deflection design
• Overload protection
• NEMA rated panels
• Oil cooler
• JIC/NFPA standard components
• IEC rated electric components
• Full tonnage throughout stroke or cycle

Special Feature:

• These presses offer maximum access to tool area for tool changing & component feeding Applications
• Slide guidance can be either twin pillars or face slide.
• Hydraulic power pack is inbuilt & all valves are manifold mounted for easy & quick maintenance & a pressure relief valve protects against overloading of the press.

Optional Accessories:

• Light curtains
• Pressure strips
• Remote system monitoring
• Remote diagnostics
• Die tables
• Die loaders
• Die clamping
• Die storage
• Local or centralized controls

Product Details:

Frame Contraction: Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron/steel fabricated and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.

Product Details:

Frame Contraction: Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron/steel fabricated and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.

Product Details:

Frame Contraction: Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron/steel fabricated and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.

Product Details:

Frame Contraction: Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron/steel fabricated and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.

Product Details:

Frame Contraction: Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron/steel fabricated and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.

Product Details:

Frame Contraction: Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron/steel fabricated and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.

Product Details:

Frame Contraction: Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron/steel fabricated and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.

Product Details:

Frame Contraction: Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron/steel fabricated and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.

Product Details:

Frame Contraction: Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron/steel fabricated and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.

Product Details:

Frame Contraction: Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron/steel fabricated and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.

Product Details:

Frame Contraction: Frame fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable of generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.

Product Details:

Frame Contraction: Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron/steel fabricated and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.

Product Details:

Frame Contraction: Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron/steel fabricated and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.183

Product Details:

Frame Contraction: Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron/steel fabricated and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.183

Product Details:

Frame Contraction: Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron/steel fabricated and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.

Product Details:

Frame Contraction: Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

 Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron/steel fabricated and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.

Product Details:

Frame Contraction: Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron/steel fabricated and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.