Rajesh Machines India LLP
Rajkot, Gujarat
GST No. 24AAUFR3820P1ZK
TrustSEAL Verified
Call 08048618726 53% Response Rate
SEND EMAIL
Product Details:
| Brand | Rajesh |
| Capacity | 60Ton |
| Usage/Application | Industrial |
| Automation Grade | Semi Automatic |
| Size | 60T/2000 |
| Max Sheet Width | 2 meter |
Frame Contraction: Frame is made of steel fabrication construction of interlock robust design. Machine are constructed with safe guard against undesired deflections and breakage. This frame distributes the stresses, supporting the bed directly on the frame. The double support shoe of frame gap provide extremely high rigidity, alignment, accuracy and keeps frame structure at the right angles to the bed.
Table & Slide (Ram): Table and upper beam are straight and parallel of the working surface under the rated load. The table is accurately machined and upper surface is grinded to keep the die in correct alignment. The upper beam is guided and supported throughout the stroke by accurately machines guide ways.
Tooling: Tooling is manufactured strictly as per standard EN-31. Every step from designing metallurgical specification, heat-treatment grinding and inspection is carefully controlled. The tooling are standardized and easily replaced.
Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).
Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable of generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.
Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.
Accurate Gauging: The rigid and accurate construction of the back gauge provided with machine allows consistency in width of sheet being Bend.
Product Details:
| Brand | Rajesh |
| Usage/Application | Industrial |
| Size | 40T/2500 mm |
| Automation Grade | Semi Automatic |
| Cutting Load | 30-60 ton |
| Max Sheet Width | 2500 |
Frame Contraction: Frame is made of steel fabrication construction of interlock robust design. Machine are constructed with safe guard against undesired deflections and breakage. This frame distributes the stresses, supporting the bed directly on the frame. The double support shoe of frame gap provide extremely high rigidity, alignment, accuracy and keeps frame structure at the right angles to the bed.
Table & Slide (Ram): Table and upper beam are straight and parallel of the working surface under the rated load. The table is accurately machined and upper surface is grinded to keep the die in correct alignment. The upper beam is guided and supported throughout the stroke by accurately machines guide ways.
Tooling: Tooling is manufactured strictly as per standard EN-31. Every step from designing metallurgical specification, heat-treatment grinding and inspection is carefully controlled. The tooling are standardized and easily replaced.
Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).
Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable of generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.
Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.
Accurate Gauging: The rigid and accurate construction of the back gauge provided with machine allows consistency in width of sheet being Bend.
Product Details:
| Brand | Rajesh |
| Usage/Application | Industrial |
| Material | Mild Steel |
| Size | 100T/2500 |
| Max Sheet Width | 2500 mm |
| Length | 2500 mm |
| Tonnage | 100T |
Frame Contraction: Frame is made of steel fabrication construction of interlock robust design. Machine are constructed with safe guard against undesired deflections and breakage. This frame distributes the stresses, supporting the bed directly on the frame. The double support shoe of frame gap provide extremely high rigidity, alignment, accuracy and keeps frame structure at the right angles to the bed.
Table & Slide (Ram): Table and upper beam are straight and parallel of the working surface under the rated load. The table is accurately machined and upper surface is grinded to keep the die in correct alignment. The upper beam is guided and supported throughout the stroke by accurately machines guide ways.
Tooling: Tooling is manufactured strictly as per standard EN-31. Every step from designing metallurgical specification, heat-treatment grinding and inspection is carefully controlled. The tooling are standardized and easily replaced.
Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).
Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable of generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.
Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.
Accurate Gauging: The rigid and accurate construction of the back gauge provided with machine allows consistency in width of sheet being Bend.
Product Details:
| Max Sheet Width | 2 meter |
| Usage/Application | Sheet Bending |
| Brand | Rajesh |
| Control Type | Non-CNC |
| Size | 30T/2000 mm |
| Capacity | 30T |
| Length | 2000 mm |
NC BACK GAUGE
Schneider/DELTA 7”Digital Touch Color Display
- Schneider/DELTA PLC
- Y - Axis With High Precision Liner Scale for Stroke Length Measurement and Auto Degree/Angle Bending
- X - Axis Servo Back Gauge
- Schneider/Siemens/Panasonic Servo Motor and Servo Drive
- HIWIN - Taiwan Ball Screw
- HIWIN - Taiwan Hardened and Grounded Shaft
- HIWIN - Taiwan LM Bush
- Auto Program Function
- Stroke Counter
- Inch/Single/Auto Stroke Cycle
- Storage Capacity (100 Programs and Per Program 10 Bend can Store)
Frame Contraction: Frame is made of steel fabrication construction of interlock robust design. Machine are constructed with safe guard against undesired deflections and breakage. This frame distributes the stresses, supporting the bed directly on the frame. The double support shoe of frame gap provide extremely high rigidity, alignment, accuracy and keeps frame structure at the right angles to the bed.
Table & Slide (Ram): Table and upper beam are straight and parallel of the working surface under the rated load. The table is accurately machined and upper surface is grinded to keep the die in correct alignment. The upper beam is guided and supported throughout the stroke by accurately machines guide ways.
Tooling: Tooling is manufactured strictly as per standard EN-31. Every step from designing metallurgical specification, heat-treatment grinding and inspection is carefully controlled. The tooling are standardized and easily replaced.
Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).
Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable of generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.
Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.
Accurate Gauging: The rigid and accurate construction of the back gauge provided with machine allows consistency in width of sheet being Bend.
Product Details:
| Max Sheet Width | 1500 |
| Usage/Application | Industrial |
| Brand | Rajesh |
| Control Type | Non-CNC |
| Size | 20T/1500 mm |
| Cutting Load | 20T |
NC BACK GAUGE
Schneider/DELTA 7”Digital Touch Color Display
- Schneider/DELTA PLC
- Y - Axis With High Precision Liner Scale for Stroke Length Measurement and Auto Degree/Angle Bending
- X - Axis Servo Back Gauge
- Schneider/Siemens/Panasonic Servo Motor and Servo Drive
- HIWIN - Taiwan Ball Screw
- HIWIN - Taiwan Hardened and Grounded Shaft
- HIWIN - Taiwan LM Bush
- Auto Program Function
- Stroke Counter
- Inch/Single/Auto Stroke Cycle
- Storage Capacity (100 Programs and Per Program 10 Bend can Store)
Frame Contraction: Frame is made of steel fabrication construction of interlock robust design. Machine are constructed with safe guard against undesired deflections and breakage. This frame distributes the stresses, supporting the bed directly on the frame. The double support shoe of frame gap provide extremely high rigidity, alignment, accuracy and keeps frame structure at the right angles to the bed.
Table & Slide (Ram): Table and upper beam are straight and parallel of the working surface under the rated load. The table is accurately machined and upper surface is grinded to keep the die in correct alignment. The upper beam is guided and supported throughout the stroke by accurately machines guide ways.
Tooling: Tooling is manufactured strictly as per standard EN-31. Every step from designing metallurgical specification, heat-treatment grinding and inspection is carefully controlled. The tooling are standardized and easily replaced.
Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).
Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable of generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.
Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.
Accurate Gauging: The rigid and accurate construction of the back gauge provided with machine allows consistency in width of sheet being Bend.
Product Details:
| Minimum Order Quantity | 1 Unit |
| Usage/Application | Sheet Bending |
| Material | Mild Steel |
| Brand | Rajesh |
| Control Type | Non-CNC |
| Automation Grade | Semi-Automatic |
| Size | 50T/1500 mm |
| Max Sheet Width | 1500 mm |
| Country of Origin | Made in India |
Frame Contraction: Frame is made of steel fabrication construction of interlock robust design. Machine are constructed with safe guard against undesired deflections and breakage. This frame distributes the stresses, supporting the bed directly on the frame. The double support shoe of frame gap provide extremely high rigidity, alignment, accuracy and keeps frame structure at the right angles to the bed.
Table & Slide (Ram): Table and upper beam are straight and parallel of the working surface under the rated load. The table is accurately machined and upper surface is grinded to keep the die in correct alignment. The upper beam is guided and supported throughout the stroke by accurately machines guide ways.
Tooling: Tooling is manufactured strictly as per standard EN-31. Every step from designing metallurgical specification, heat-treatment grinding and inspection is carefully controlled. The tooling are standardized and easily replaced.
Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).
Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable of generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.
Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.
Accurate Gauging: The rigid and accurate construction of the back gauge provided with machine allows consistency in width of sheet being Bend.
Product Details:
| Max Sheet Width | 6 mm |
| Usage/Application | Industrial |
| Material | Mild Steel |
| Capacity | 125T/2500 mm |
| Brand | Rajesh |
| Model Name/Number | RP-Bend 125T/2500 mm |
| Automation Grade | Semi-Automatic |
| Power | Hydraulic |
| Warranty | 1 Year |
| Country of Origin | Made in India |
Frame Contraction: Frame is made of steel fabrication construction of interlock robust design. Machine are constructed with safe guard against undesired deflections and breakage. This frame distributes the stresses, supporting the bed directly on the frame. The double support shoe of frame gap provide extremely high rigidity, alignment, accuracy and keeps frame structure at the right angles to the bed.
Table & Slide (Ram): Table and upper beam are straight and parallel of the working surface under the rated load. The table is accurately machined and upper surface is grinded to keep the die in correct alignment. The upper beam is guided and supported throughout the stroke by accurately machines guide ways.
Tooling: Tooling is manufactured strictly as per standard EN-31. Every step from designing metallurgical specification, heat-treatment grinding and inspection is carefully controlled. The tooling are standardized and easily replaced.
Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).
Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable of generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.
Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.
Accurate Gauging: The rigid and accurate construction of the back gauge provided with machine allows consistency in width of sheet being Bend.
Additional Information:
Product Details:
| Max Sheet Width | 10 mm |
| Usage/Application | Industrial |
| Capacity | 100T/3000 |
| Brand | Rajesh |
| Automation Grade | Semi Automatic |
| Model Name/Number | RP-Bend 100T/3000 |
| Power | Hydraulic |
| Warranty | 1 Year |
| Country of Origin | Made in India |
| Material | Mild Steel |
Frame Contraction: Frame is made of steel fabrication construction of interlock robust design. Machine are constructed with safe guard against undesired deflections and breakage. This frame distributes the stresses, supporting the bed directly on the frame. The double support shoe of frame gap provide extremely high rigidity, alignment, accuracy and keeps frame structure at the right angles to the bed.
Table & Slide (Ram): Table and upper beam are straight and parallel of the working surface under the rated load. The table is accurately machined and upper surface is grinded to keep the die in correct alignment. The upper beam is guided and supported throughout the stroke by accurately machines guide ways.
Tooling: Tooling is manufactured strictly as per standard EN-31. Every step from designing metallurgical specification, heat-treatment grinding and inspection is carefully controlled. The tooling are standardized and easily replaced.
Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).
Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable of generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.
Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.
Accurate Gauging: The rigid and accurate construction of the back gauge provided with machine allows consistency in width of sheet being Bend.
Additional Information:
Product Details:
| Minimum Order Quantity | 1 Unit |
| Max Sheet Width | 4 mm |
| Usage/Application | Industrial |
| Material | Mild Steel |
| Capacity | 100T/4000 mm |
| Brand | Rajesh |
| Model Name/Number | RP-Bend 100T/4000 |
| Automation Grade | Automatic |
| Power | Hydraulic |
| Country of Origin | Made in India |
Frame Contraction: Frame is made of steel fabrication construction of interlock robust design. Machine are constructed with safe guard against undesired deflections and breakage. This frame distributes the stresses, supporting the bed directly on the frame. The double support shoe of frame gap provide extremely high rigidity, alignment, accuracy and keeps frame structure at the right angles to the bed.
Table & Slide (Ram): Table and upper beam are straight and parallel of the working surface under the rated load. The table is accurately machined and upper surface is grinded to keep the die in correct alignment. The upper beam is guided and supported throughout the stroke by accurately machines guide ways.
Tooling: Tooling is manufactured strictly as per standard EN-31. Every step from designing metallurgical specification, heat-treatment grinding and inspection is carefully controlled. The tooling are standardized and easily replaced.
Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).
Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable of generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.
Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.
Accurate Gauging: The rigid and accurate construction of the back gauge provided with machine allows consistency in width of sheet being Bend.
Additional Information:
Product Details:
| Max Sheet Width | 2 meter |
| Material | Mild Steel |
| Usage/Application | Industrial |
| Size | RP-Bend 100T/*2000 |
| Brand | Rajesh |
| Automation Grade | Semi Automatic |
| Model | RP-Bend 100T/2000 |
Frame Contraction: Frame is made of steel fabrication construction of interlock robust design. Machine are constructed with safe guard against undesired deflections and breakage. This frame distributes the stresses, supporting the bed directly on the frame. The double support shoe of frame gap provide extremely high rigidity, alignment, accuracy and keeps frame structure at the right angles to the bed.
Table & Slide (Ram): Table and upper beam are straight and parallel of the working surface under the rated load. The table is accurately machined and upper surface is grinded to keep the die in correct alignment. The upper beam is guided and supported throughout the stroke by accurately machines guide ways.
Tooling: Tooling is manufactured strictly as per standard EN-31. Every step from designing metallurgical specification, heat-treatment grinding and inspection is carefully controlled. The tooling are standardized and easily replaced.
Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).
Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable of generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.
Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.
Accurate Gauging: The rigid and accurate construction of the back gauge provided with machine allows consistency in width of sheet being Bend.
Product Details:
| Minimum Order Quantity | 1 Unit |
| Usage/Application | Sheet Bending |
| Material | Mild Steel |
| Capacity | 100 Ton |
| Control Type | Non-CNC |
| Automation Grade | Semi-Automatic |
| Size | 100T/4000 |
| Max Sheet Width | 4 meter |
| Brand | Rajesh |
| Country of Origin | Made in India |
Frame Contraction: Frame is made of steel fabrication construction of interlock robust design. Machine are constructed with safe guard against undesired deflections and breakage. This frame distributes the stresses, supporting the bed directly on the frame. The double support shoe of frame gap provide extremely high rigidity, alignment, accuracy and keeps frame structure at the right angles to the bed.
Table & Slide (Ram): Table and upper beam are straight and parallel of the working surface under the rated load. The table is accurately machined and upper surface is grinded to keep the die in correct alignment. The upper beam is guided and supported throughout the stroke by accurately machines guide ways.
Tooling: Tooling is manufactured strictly as per standard EN-31. Every step from designing metallurgical specification, heat-treatment grinding and inspection is carefully controlled. The tooling are standardized and easily replaced.
Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).
Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable of generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.
Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.
Accurate Gauging: The rigid and accurate construction of the back gauge provided with machine allows consistency in width of sheet being Bend.
Product Details:
| Max Sheet Width | 2 meter |
| Size | 80T/2000 |
| Material | Mild Steel |
| Brand | Rajesh |
| Usage/Application | Industrial |
| Automation Grade | Semi Automatic |
Frame Contraction: Frame is made of steel fabrication construction of interlock robust design. Machine are constructed with safe guard against undesired deflections and breakage. This frame distributes the stresses, supporting the bed directly on the frame. The double support shoe of frame gap provide extremely high rigidity, alignment, accuracy and keeps frame structure at the right angles to the bed.
Table & Slide (Ram): Table and upper beam are straight and parallel of the working surface under the rated load. The table is accurately machined and upper surface is grinded to keep the die in correct alignment. The upper beam is guided and supported throughout the stroke by accurately machines guide ways.
Tooling: Tooling is manufactured strictly as per standard EN-31. Every step from designing metallurgical specification, heat-treatment grinding and inspection is carefully controlled. The tooling are standardized and easily replaced.
Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).
Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable of generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.
Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.
Accurate Gauging: The rigid and accurate construction of the back gauge provided with machine allows consistency in width of sheet being Bend.
Product Details:
| Usage/Application | Industrial |
| Brand | Rajesh |
| Product Type | Steel Plate |
| Power | Hydraulic |
| Automation Grade | Automatic |
| Country of Origin | Made in India |
Product Details:
| Max Sheet Width | 2 meter |
| Usage/Application | Industrial |
| Control Type | Non-CNC |
| Size | 30T/2000 |
NC BACK GAUGE
Schneider/DELTA 7”Digital Touch Color Display
- Schneider/DELTA PLC
- Y - Axis With High Precision Liner Scale for Stroke Length Measurement and Auto Degree/Angle Bending
- X - Axis Servo Back Gauge
- Schneider/Siemens/Panasonic Servo Motor and Servo Drive
- HIWIN - Taiwan Ball Screw
- HIWIN - Taiwan Hardened and Grounded Shaft
- HIWIN - Taiwan LM Bush
- Auto Program Function
- Stroke Counter
- Inch/Single/Auto Stroke Cycle
- Storage Capacity (100 Programs and Per Program 10 Bend can Store)
Frame Contraction: Frame is made of steel fabrication construction of interlock robust design. Machine are constructed with safe guard against undesired deflections and breakage. This frame distributes the stresses, supporting the bed directly on the frame. The double support shoe of frame gap provide extremely high rigidity, alignment, accuracy and keeps frame structure at the right angles to the bed.
Table & Slide (Ram): Table and upper beam are straight and parallel of the working surface under the rated load. The table is accurately machined and upper surface is grinded to keep the die in correct alignment. The upper beam is guided and supported throughout the stroke by accurately machines guide ways.
Tooling: Tooling is manufactured strictly as per standard EN-31. Every step from designing metallurgical specification, heat-treatment grinding and inspection is carefully controlled. The tooling are standardized and easily replaced.
Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).
Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable of generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.
Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.
Accurate Gauging: The rigid and accurate construction of the back gauge provided with machine allows consistency in width of sheet being Bend.