Power Press

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Additional Information:

• Delivery Time: 4 Weeks

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Additional Information:

• Delivery Time: 4 weeks

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: Frame is fabricated from IS-2062 graded rolled steel plates table and cutting beam deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

 Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron/steel fabricated and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Cylinder: The cylinder bodies are precisely made from forged steel material duly bored and fine honed or long sealing life. The piston rods are made from EN-8 material having low carbon contents. The piston rod is hard chrome platted (0.200 micron).

Hydraulic System: The compact blocks eliminate the leakage chances and also reduces the hydraulic pipes. This low noise hydraulic system is placed on the rear side of machine, on the rear side of machine, on top between two side plates. Pressure relief values is provided to safe guard the system and machine from overload. The hydraulic system is driven by an electric motor of reputed brand and is coupled with a pump capable if generating more than the required pressure. Pressure gauge for system pressure, back pressure and holding pressure are providing on top of oil tank for quick reference.

Electrical Control Panel: The electrical control panel is located on the left hand side of the machine. It is assembled from the internationally reputed parts for consistent performance, reliability and availability, if need to be replaced. It is wire cleanly and labeled/ferruled properly as per the international practices to help easily locates any fault and replaces components conveniently.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Mechanical Power Press 30 Ton C-Type is a heavy-duty machine designed for metal forming operations like punching, blanking, and bending. Its C-type frame ensures easy access, rigidity, and high precision under a 30-ton pressing capacity.

Additional Information:

• Delivery Time: 4 Week

Product Details:

Power Press 75 Ton is a high-capacity mechanical press used for heavy-duty metal forming tasks such as punching, shearing, and deep drawing. It delivers 75 tons of pressing force with precision, making it ideal for industrial production.

 4o

Additional Information:

• Delivery Time: 4 Week

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: High Speed Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Rolling Key Clutch: Made of alloy steel for positive engagement and continues operation heavy three key ways. Single rolling key system is incorporated in the machine ensuring easy and efficient working of the machine.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

Lubrication System: Single shot lubrication provides oil to all the lubrication point, where necessary, thus all bearing parts and guide surface etc.

Product Details:

Frame Contraction: C-Frame Pneumatic Press fabricated from IS-2062 graded rolled steel plates. Frame is deeply reinforced and fines machines after stress reliving. The interlocked design put the direct support to frame. These frames are strain free and eliminate welds at load supports. Thus the accuracy of the machine is never disturbed.

Table & Slide (Ram): Table and Slide are made of high grade heavy duty cast iron and properly seasoned. They are perfectly aligned, to each other to obtain high accuracy and precision press operation.

Main and Pinion Shaft: Shaft is made of special alloy steel machined to close accuracy and fitted in bronze bushes for smooth working, longer life and accuracy.

Gears: Gears are of steel cast of fabricated. Gear teeth are generated by precision hobbing machine.

Flywheel: Properly sized flywheel is made of high grade cast iron, for strong and releasing adequate energy for the cutting operation, and properly balanced for smooth running.

High Quality Crank Shaft: The strong crank shaft with outstanding rigidity ensures that accuracy can be maintained under qualified standard and extends the life of tooling.

Auto Lubrication System: The auto lubrication system with default monitor ensures high reliable operation.

Dual Safety Valve: The interlock mechanism on the dual valve keeps the clutch and brake from mis-actuation when valve is default.

Pneumatic dry Clutch: The fail-safe, pneumatically operated clutch brake combination is designed to provide excellent slide motion control even at high speeds. Adequate energy required for blanking operation is ensured by optimized design of the flywheel.